Can I put LED lights in a fluorescent fixture?


Can I put LED lights in a fluorescent fixture? Answer: Great question – and the answer is yes, an LED tube light can be installed in a traditional fluorescent tube light fixture, without the ballast. Bypassing the ballast in a tube light fixture has the advantage of being more energy efficient – you can expect to save another 5 – 10% of energy use per fixture.

Can LED lights be used in fluorescent fixtures? To convert a fluorescent light fixture to use LED bulbs, you can either use LED bulbs that are compatible with the existing fluorescent ballast (plug-and-play tubes) or you can rewire the fixture to bypass the ballast and replace with sockets with non-shunted lampholders.

Do I need to remove the ballast to use an LED bulb? Bypass the ballast linear LEDs – also known as line voltage or direct-wire linear LEDs – work straight off the line voltage flowing directly to the sockets, requiring you to remove the original fluorescent ballast.

Are LED lights brighter than fluorescent? You will not experience any kind of flickering or dark spots left at any of the indoor places. The LED tube lights are noticeably brighter than fluorescent tubes and you don’t get exposed to any kind of harmful rays such as UV/IV rays as well that can damage your eyes and can result in skin allergies as well.

Can I put LED lights in a fluorescent fixture? – Related Questions

What kind of ballast do I need for LED lights?

Type A LED tubes need an existing T8 electronic ballast to operate. If you have T8 electronic ballasts this makes installation very easy. All you need to do is remove the existing T8 fluorescent lamp and install a new T8 LED Type A lamp.

Will LED bulbs work if ballast is bad?

BENEFITS OF THE BALLAST BYPASS

No matter how new or well maintained your ballasts are, they will all eventually go bad. When an LED bulb does burn out (between 15-20 years in most cases) you simply replace the bulb, which is much more cost-effective and less time consuming than replacing an entire ballast.

How much does it cost to change fluorescent lights to LED?

Upgrading Incandescent/CFL Replacements to LED Costs. Replacing incandescent and compact fluorescent lamp (CFL) bulbs with LED bulbs will cost about $6 – $9 for a 10-Watt LED. Therefore, if you change 24 bulbs, it will cost $144 – $216 to replace those all at once.

Can you use 4ft LED bulbs in fluorescent fixtures?

In short, YES!

New linear LED tube bulbs are simple plug and play and ballast compatible. You will simply need to remove your fluorescent bulb and plug in your LED replacement.

Do I still need a starter with an LED tube?

Conventional fluorescent tubes need a starter. This starter provides ignition voltage. Naturally, this isn’t necessary for LEDs, so the ignition voltage is superfluous. If you want to replace a traditional fluorescent bulb with an LED, then you must install a dummy starter or bypass the standard starter manually.

Will plug and play LED work without ballast?

What is a plug and play? A plug and play LED is a fixture where you can install LED bulbs to what was once a fluorescent bulb. This is an easy solution and requires minimal effort on your part. Since it works with the existing ballast, there is no need for rewiring or ballast removal.

What are the yellow wires on a ballast?

The common yellow wires connect from the ballast to push-in connectors on one of the right holders of lamp 1 or 2. Two yellow wires connect the common lampholders together.

What is a 100 watt bulb in LED?

When you see a label say “100-Watt LED equivalent” that does not mean that the bulb actually uses 100 Watts, it means that it produces an amount of light equivalent to a 100-Watt incandescent bulb.

Is it worth switching to LED bulbs?

So most people will be able to recoup the cost of a new LED bulb in just over three months. In addition to saving money, LEDs can save you time — with fewer trips to the store and up the ladder. They last about 25,000 hours. By comparison, incandescent bulbs last just 1,200 hours, and compact fluorescents, 8,000 hours.

Are LED lights better for your eyes than fluorescent?

Luckily, “warm light” CFLs (Compact Fluorescent Lights) are okay for your eyes, as well as being much more efficient. They do emit UV rays, but a much smaller amount. Remember that LEDs are not as good at emitting light in all directions, however, so you’ll have to think strategically about where to place them.

What does a driver do for LED lights?

An LED driver rectifies higher voltage, alternating current to low voltage, direct current. LED drivers also protect LEDs from voltage or current fluctuations. A change in voltage could cause a change in the current being supplied to the LEDs.

What does a LED ballast do?

A ballast regulates the current to the lamps and provides sufficient voltage to start the lamps. Lamps have no regulator and can draw too much or too little power on their own. The ballast makes sure that the amount of current being provided to the lamp is not more than the specification of the light.

What is the difference between a driver and a ballast?

The driver is an electrical device that regulates power to your LED lights. It’s comparable to a ballast for fluorescent lighting systems. In short, the driver keeps your LEDs running safely and consistently, even when the LED’s electrical properties shift due to fluctuating temperatures.

How do you know if it’s the bulb or ballast?

Take out your current bulbs and replace them with the new bulbs. If the bulbs fail to light up, then 9 out of 10 times the ballast is culprit. If the ballast is good, an analog multimeter has a needle that will sweep to the right across the measuring scale. If the ballast is bad, then the needle won’t move.

What can I replace fluorescent lights with?

Replacement choices include pendant lighting, flush-mount ceiling fixtures, track lighting, monorail lighting, potrack lighting and more. You can even skip the ceiling-mounted light and instead install a couple of wall sconces.

How do you make fluorescent lights look better?

One way to make fluorescent light look better is to use colored film to cover lights, changing the spectrum that reaches your eyes.

Can you replace T5 with LED?

T5 LED Tube Lights and LED Fluorescent Tube Replacements. Reduce the time and money spent relamping your T5 fluorescent fixtures in your home or business by upgrading to LED with these LED T5 tube lights from 1000Bulbs.com!

How do I know if my ballast is T8 or T12?

You will see either T8 or T12 stamped on one side near the end with the prongs. You also will see the lamp’s rated wattage, usually 32 watts for T8 and 40 watts for T12. Measure the diameter of the lamp. T12 lamps are larger than T8 lamps, with a 1 ½-inch diameter.

Does a T8 LED tube need a starter?

The T8 LED Tube Dummy Starter should be used for replacing your old fluorescent tubes with LED TL Tubes in the same fixture. Note! You do not need a T8 LED Tube Dummy Starter when installing LED TL tubes in LED TL fixtures. These fixtures are designed in such a way that you no longer need a starter.

Do you need to be an electrician to change a ballast?

Yes. As a matter of fact, you do need a lock out tag out device in place for changing a ballast. ‘An electrician is replacing the ballast on a fluorescent light. The electrician uses the light switch on the wall to de-energize the florescent light.

What LED replaces a 60W bulb?

A 60-watt incandescent light bulb can be replaced with a 10-watt LED.


Leave a Reply

Your email address will not be published. Required fields are marked *