Can you convert a side post battery to a top post? Replace each battery terminal with a post converter. These parts give you a safe and effective way to convert a side design to a top-post configuration. The converters should stretch between the sides and end up along the topside of the battery. Each terminal must be made of lead for the best conductivity.

Can you change post on battery? If the battery terminals have minor corrosion, just remove them and clean them and the battery posts with a wire brush. But if either or both terminals don’t clamp tight or the corrosion is eating away at the metal, they should be replaced.

Why use side post battery? You know that the reason for the side post terminal was to prevent the corrosion which was a part of most top terminal installs after a few years. Side terminal batteries seldom have terminal corrosion issues in my experience.

Will AutoZone change my battery terminals? If so, AutoZone sells replacement terminals and terminal end kits. Once you clean your terminals and/or replace them, clean the battery posts and the top of the battery, then wipe them off with a rag.

Can you convert a side post battery to a top post? – Related Questions

Do battery posts unscrew?

Loosen the nut that holds the terminal onto the negative post using a socket wrench. The nut will be located to the left of the terminal. Lift the terminal off the negative battery post. If needed, pry the terminal open with a screwdriver, or gently wiggle the connector until it loosens.

Can I connect remote wire to battery?

No, run the remote wire to the remote out on the back of the headunit. You can then install a switch on the remote wire to turn it on or off, but if you run it directly to the battery you will have problems because the amps will always be on, and you will kill your battery.

Do you connect AMP to positive or negative?

It is important that you keep the polarity of your speaker wiring straight. This means that each positive terminal of the amp connects to a positive terminal of a speaker — and the same goes for the negative terminals.

Which battery terminal do I connect first?

“Positive first, then negative. When disconnecting the cables from the old battery, disconnect the negative first, then the positive. Connect the new battery in the reverse order, positive then negative.”

Why does my car battery terminals keep corroding?

Corrosion happens on the battery terminals when hydrogen gas is being released from the acid in the battery. This acid mixes with other things in the air under the hood of your vehicle, causing the corrosion you can see. Some batteries are “maintenance free” which means you don’t need to check the water levels inside.

What is a top post battery terminal?

Replaces corroded terminals on 6-12-volt batteries. Battery cable terminal is designed to reduce the risk of lead contamination. Compatible with 1-6-gauge automotive cables.

What is a side post battery?

A side post battery has the positive and negative terminals located on the side of the battery rather than on the top of the battery. They are being used every time you run the car as the car battery supplies the power necessary to start your car.

When did GM start using side post batteries?

First, the division will supply as original equipment on about 80 percent of General Motors car divisions’ 1971 model cars, the new Delco sealed side terminal (ST) battery. This new battery design was introduced by Delco-Remy in 1969, but has been available only in the after-market.

Can you use Coke to clean battery terminals?

In many cases, ignition problems can be fixed by cleaning the car battery corrosion from the terminals and cables, which couldn’t be simpler. Next, slowly pour a small amount of Coca Cola over any corroded areas. The Coke will bubble and eat away at the rust and corrosion.

How much does it cost to change battery terminals?

In most cases, the battery terminals, unfortunately, will be part of the battery and if the terminals are damaged, you will have to replace the entire battery. If this were the situation, and in most cases, it will be, plan on spending anywhere from $50 to $150 depending on the make/model of the vehicle.

How do you get corrosion off battery terminals?

Thoroughly mix a tablespoon of baking soda with a cup of hot water. With an old toothbrush, dip you brush into this solution and scrub at the corrosion. If the corrosion is too hard to remove, consider buying a battery terminal cleaner brush. Completely dry the battery.

Can you use wd40 to loosen battery terminals?

WD-40 Specialist Fast Drying Contact Cleaner can act as a protective layer, applied on the poles and terminals of the car battery and successfully eliminate oil, deposits of grease and mud.

What happens if you don’t disconnect the negative battery cable?

Contact between the negative battery terminal and the battery, even if the cable is not clamped onto the battery, may reactivate the electrical system within the car. This would negate all the reasons you have done this much work to ensure the cable is disconnected.

What happens if you disconnect the positive terminal first?

It’s important to disconnect the negative side of the battery first, otherwise you can cause an electrical short if the positive is removed first.

Can a melted battery post be repaired?

EV driving currents can easily approach or even exceed 500 amps, and these poor connections generate heat – sometimes enough to literally melt the battery post. If you’re lucky, the car just stops running. A good battery shop can often repair it by casting a new post onto it.

Can you solder a battery post?

Yes, it’s safe as long as you don’t use excessive heat. NiMh batteries are relatively stable. Practice some with plain wire and make sure your soldering is up to par. To help with the soldering, you can use some flux such as Chip Quik Flux.

How many volts should a remote wire have?

While in the ON position, there should be 12+ volts at the remote turn on wire. If you have 12+ volts while the ignition is OFF, the remote turn on wire is connected to constant power.

How do you connect two amplifiers together?

The best way to wire multiple amps to a single power cable is to use a power distribution block. That allows you to use a single cable for most of the run, including the crucial portion that passes through the firewall and then to use shorter individual cables to actually connect to each amplifier.

Can you run power wire next to speaker wire?

It is really okay to run speaker wires along power wires. In theory it shouldn’t be done, but in a car environment, you won’t notice it. There was a debate on this before. Because the voltage is only 12.5v, it’s not high enough to cause interference.

Why is my amp not getting power?

If the remote turn-on wire doesn’t have power, your amp won’t turn on. If it doesn’t, you’ll want to check for any inline fuses and verify that the wire isn’t loose, corroded, or shorted out somewhere. If the remote and power wires both check out okay, the next thing to look for is continuity on the ground wire.