Should a toilet flange spin? Unless you are rotating the toilet less than a few degrees, you have to rotate the flange itself before the bolts can slide into the position you want.

Should toilet flange be flush with floor? When you install your toilet flange, it should be installed on top of the finished floor, and it should also be installed perfectly level. If your flange sits even or below the floor, then it’s wrong. It has to sit evenly on top of the finished floor.

How tight should toilet flange be? The toilet bolts should not be overtightened, but they should be tight. If you hear the sound of metal on porcelain, stop tightening. But if you still feel the bolts tightening against the wax ring, keep going.

Why do toilet anchor bolts rust? Moisture around the base of the toilet can corrode the anchor bolts. This moisture may be the result of water escaping from the toilet because of an imperfect seal or, in basements near sea level, it may come from condensation or poor drainage.

Should a toilet flange spin? – Related Questions

Can you replace toilet bolts without removing toilet?

You can’t replace a closet bolt without removing the bowl. Pull the bowl, and next time pick up brass bolts.

What happens if toilet flange is too high?

When your toilet flange is too high, your toilet may leak water and rock back and forth when used. Both the leaking and the rocking can warp or break the floor. A leaking flange can also rot the subfloor and lead to the accumulation of mildew and mold.

Can a toilet flange be too low?

But if you add new flooring up to the edge of the flange, or if the flange wasn’t installed properly to begin with, the flange may sit too far below the flooring level. Left this way, the toilet may not seal tightly against the drain, creating the potential for leaks around the base of the toilet.

What happens if toilet flange is broken?

A toilet flange has a metal or plastic ring that holds the toilet to the floor, and when the ring breaks, it can render the toilet unusable. If the toilet rocks because the flange is no longer holding it securely, the wax ring seal can break, water can begin to seep out and problems quickly multiply.

What does a bad toilet flange look like?

SIGNS OF A BAD TOILET FLANGE:

Rocking toilet. Sewer smells. Leak from the base of the toilet. Toilet leaks on floor.

Should toilet flange sit on top of tile?

The toilet flange needs to be on top of the finished floor. Meaning the bottom edge of the flange needs to be on the same plane as the toilet. So if your toilet sits on the tile, the flange needs to be on top of the tile too. The spacing of the toilet exit “horn” and sealing surface is designed for this height.

Should a toilet sit flat on the floor?

Level the Toilet

If it does not sit perfectly flat, it will rock and is more likely to leak over time. To correct this problem, slip toilet shims between the base and the floor to stop the rocking before bolting it down.

Why is my new toilet rocking back and forth?

One of the most common things that causes a toilet to rock back and forth are loose flange bolts. These are the bolts that hold the toilet down at an even level with the floor in your bathroom. A toilet does not screw directly into the ground. Instead, it screws into what’s called a toilet flange, or a closet flange.

Why does my toilet moves side to side?

If the flange is a little higher than the surrounding flooring, the toilet becomes raised slightly in the center, allowing it to rock to either side. This problem can develop over time, such as when the wax seal becomes faulty or when a surrounding floor settles a little.

How often should you replace the wax ring on a toilet?

It requires no maintenance and can last 30 or more years, often as long as the toilet itself. But sometimes wax rings can dry out, crumble, and fail prematurely. When that happens, they need to be replaced. The telltale sign of wax ring failure is water leaking out from around the base of the toilet.

What holds toilet to floor?

The toilet flange, also known as a closet flange, is the part of the toilet that secures the unit to the floor and connects to the drain pipe. Usually made of PVC, rubber or metal, this piece is circular in shape and usually secured in place with a few bolts.

Can you reuse toilet flange bolts?

Remove the old hold-down bolts – don’t reuse them. You may want to clean and paint the wall behind the toilet. Also, inspect the toilet flange for sound condition. It should stick up about 1/2″ from the finished bathroom floor.

Does a toilet flange need to be screwed down?

The flange should be fastened to the floor. Dry fit the toilet to make sure it doesn’t rock. If it does rock, use shims to prevent rocking – just tightening the bolts probably will not stop the rocking but will risk cracking the toilet or breaking the flange.

Can you shim a toilet flange?

How to Level a Toilet Using Toilet Shims. Toilet shims are thin plastic or rubber tabs that are used to level a toilet. You can also use homemade wooden shims or stainless steel coins. If a toilet is installed on an uneven floor or if the toilet flange is too high off the floor, the toilet will need to be shimmed.

Should you glue a toilet flange?

pvc flange should be glued into a pvc pipe. IT would have been less of a problem if a plumber had made the replacement. Use a “good” flange and you will not have to do it again. Caulk is NOT glue.

Can you use 2 wax rings when installing a toilet?

You can certainly install a toilet with multiple wax rings, in fact sometimes it is necessary to make sure you don’t have a leak. You can buy an extra-thick wax ring, or you can just buy two rings and stack one on top of the other.

Is there something better than a wax ring?

Why Better Than Wax? This innovative wax-free toilet seal fits any drain, any toilet, can be repositioned during installation, and excessive plunging won’t cause leaks. Better Than Wax includes a stackable wax-free seal, slide-on spacer, and no rust brass bolts and hardware.

How thick is an extra-thick wax ring?

If it’s at the same level, or no more than 1/4 inch below it, a regular wax ring, which is between 3/4 and 1 inch thick, is all you need. If the flange is recessed deeper than that, you need an extra-thick wax ring, which is about an inch thicker than a regular one.

How long does it take to repair a toilet flange?

A straight toilet retrofit takes approximately four to six hours. If you have to repair the flange, however, you could spend the entire day working on the toilet. The bathroom will probably be out of commission for several days if you need to do subfloor repair.

Should you tile around or under a toilet?

The bathroom fitters are unanimous—if you’re looking for a high quality finish, with a better seal against water damage, then always tile the floor first. The floor will be sealed a lot better with the tiles being laid under the toilet. 2. It is also easier to do this rather than trying to cut tiles around the toilet.

What happens when wax ring goes bad on toilet?

Ceiling or Floor Damage

Sometimes, if a plumber caulked around the toilet during installation, water won’t seep from the base when the wax ring goes bad. In fact, toilet leaks that get into the floor or ceiling cause serious damage that could end up with the toilet falling through the floor. Yes, this does happen.