What is PGM on alarm panel? <Back. A very common question we get with people looking at buying DSC PowerSeries or from those at already have one is: "What is a PGM?" First PGM stands for 'programmable output'. So a PGM is a programmable negative trigger output. What does this mean? You can think of a PGM as an on off switch like a light switch.
What is PGM programming? The Program (PGM) command is used in a CL source file to identify the start of a CL program or ILE CL procedure that is to be compiled and to specify the parameters that are to be received by the procedure after it is compiled.
What does DT mean on alarm panel? Dual Technology (DT), also called ‘Dualtec’ detectors, comprise a PIR and a Microwave detector in the same unit. The basic operation of these detectors are that both elements within the detector have to be triggered to create an alarm activation.
What is a PGM output? So a PGM is a programmable negative trigger output. What does this mean? You can think of a PGM as an on/off switch like a light switch. It will be connected to something to provide power that can be turned on or off. The system will flip the switch based on what PGM type you program it for.
What is PGM on alarm panel? – Related Questions
What is a paradox PGM?
Magellan 2-Way Wireless PGM. 2-way communication allows the 2WPGM to receive commands from MAGELLAN Transceivers and then confirm the command. Backup Alarm Reporting option (activates PGM output if communication between the MAGELLAN All-In-One-Consoles and the 2WPGM is lost)
What is a grade 3 intruder alarm?
Grade 3 systems are designed to combat burglars and attackers with advanced knowledge, tools and equipment (including portal electronic devices). The system is comprehensive and protects all potential entry points of a building. High risk homes and lots of commercial properties fall into this category.
What is a protection loop trouble?
A Protection Loop Short indicates that you might have some faulty wiring for a particular zone or a faulty alarm panel. This wiring or alarm panel fault requires a technician to attend and check the system. If the signal persists, please call during business hours to arrange a technician.
How do I find my DSC installer code?
Default Master and Installation codes for DSC systems
Depending on the type of system you have, the default installer code will be 5555, 5010, 1550, or 1500. To get into programming you’ll press * 8 then the installer code and then you’ll see a red lock appear letting you know you’re in programming.
How do I know what zones My DSC alarm?
If you do not have a Ready light (*), press EXIT button until keypad beeps. LCD display will show what zone is open. Close door or window and check for ready light. If motion detector is open, stop movement and check for ready light.
What is the installer code for DSC?
The default installer code for a DSC is 5555. The installer code is the code that is used to get into the DSC programming mode so you can set the system up and make changes to panel programming. Having the installer code is the most important part of setting up the system.
Is a paradox true?
A paradox is a logically self-contradictory statement or a statement that runs contrary to one’s expectation. It is a statement that, despite apparently valid reasoning from true premises, leads to a seemingly self-contradictory or a logically unacceptable conclusion.
What are the 3 main types of alarms?
Before jumping into our overview, here is a more in-depth analysis of the 3 main types of alarms you may be looking for: fire alarm, burglary alarm, and intrusion detection.
What is a level 4 alarm system?
The Autowatch 446 RLi is a level 4 insurance approved alarm system. It has an ultrasonic sensor, an immobiliser and a anti hijack facility. Categories: Autowatch car alarms, Car Alarms and Central Locking, Car alarms and security.
Where would you expect to find a Grade 3 alarm?
An EN50131 grade 3 alarm system is sophisticated enough to protect against this higher threat of crime and is usually installed at most commercial premises such as a newsagent or a department store.
What is the difference between grade 2 and grade 3 alarms?
Grade 2 Intruder Alarms – Premises of a higher risk of an intruder or theft due to valuables kept theft on site. Grade 3 Intruder Alarms – Premises at substantial risk from intruders due to high-value contents. Grade 4 Intruder Alarms – Premises has a very high risk of being targeted by organised criminals.
How many smoke detectors can you have in one loop?
How many smoke detectors can you have in one loop? There is a maximum number to interconnect smoke detectors, which are 12 if we are referring to the NFPA 72 standards. Then you must ensure at all times that each of the smoke alarms offers the necessary compatibility to interconnect.
Why do hard wired smoke detectors go off for no reason?
Hard wired smoke detectors can go off randomly if you need to change the batteries. Smoke detectors can go off for no obvious reason when there is steam or high humidity in the house, as well as burnt food. Clean the smoke detector itself if it is dusty as that can set it off randomly as well.
What is protection loop?
Loop protection increases the efficiency of STP, RSTP, and MSTP by preventing ports from moving into a forwarding state that would result in a loop opening up in the network. When loop protection is enabled, the spanning-tree topology detects root ports and blocked ports and makes sure both keep receiving BPDUs.
What does sleep mean on alarm?
Sleep Mode is a system mode that ignores all proactive and real-time tests, parameters, and quiets all alarm notifications, effectively putting the Flo System to sleep. Sleep Mode should only be used when the home is experiencing or will experience irregular water usage which may trigger an undesired alarm.
How do I make my house alarm stop beeping during a power outage?
Go to your main control box and disconnect the battery supply, which will stop all beeping and shut your alarm system down. Once power is restored, you can reconnect your battery and your alarm system should work as before.
What does loss of sensor supervision mean?
The Loss of Sensor Supervision message refers to the interval check-in signal that the sensor uses to let the panel know it is still there and functioning. Loss of supervision is commonly seen due to a few different possible issues: Borderline or poor sensor signaling due to distance from panel.
What is StayD?
StayD is the result of two years of research and development from the Paradox R&D team. The result is a system that’s always protecting, without the risk of being unprotected, and without the uncertainty that the security system is armed or not.
What does the yellow triangle mean on my DSC alarm system?
A yellow triangle on your DSC ADT Alarm system is also known as a “trouble light.” That means if you see this symbol, your system has an issue that you need to resolve. A trouble light could mean 1 of 8 problems. To find out what the problem is, you can simply press *2 on your keypad.
What is the master code?
Master Code means the common code for each product used until the final metal layer.